Precision Painting Plus

Plaster & Drywall

When remodeling a home, people think about the granite countertops or something better than that, the number of windows in the new space. But little thought should be given to one of the most important parts of the home, the interior walls.

Most people do not think about the walls, unless there is a problem. Interior walls provide privacy and separation. They can also act as sound barriers, insulators and even offer additional fire resistance.

There are two common forms of interior wall materials, plaster and drywall. times. The earliest plaster was usually made of lime, sand, animal hair and water. An alternative to lime-based plasters, gypsum-based plasters had a faster drying time. This new form of plaster got popularity because it could speed up the building process.

As technology advanced, drywall became more durable and readily available. Drywall had surged in popularity as an interior wall material. The product now covers a majority of the interior walls in modern day homes.

Image Credit:

http://www.bobvila.com/BBS/images/BBS_UserImages/TOPIC_0x/TOPIC_8/Thread6xxx/6351-New_medicine_cabinet.jpg

Hanging Drywall

To install drywall on the ceiling and walls of a framed room, you will need an assistant, especially for the ceiling.

Quick tips for Hanging Drywall

1. Construct a pair of T-braces from 2 X 4s about an inch longer than the distance from floor to ceiling. Nail 2 X 4s about 3 feet long to one end of each longer 2 X 4 to form the Ts. Alternately, adjustable T-braces can be rented.

2. Cut drywall panels to size. Use a sharp utility knife along a straightedge to cut drywall. After you make the cut through the face paper, place the board over a length of 2 X 4 laid flat on the floor, or some other type of support, and snap the scored section down.

3. Install drywall panels on the ceiling. If possible, try to span the entire width with a single sheet of wallboard to reduce the number of joints.

4. Drive nails at 6-inch intervals into all the joists covered by the sheet. Start in the center of the drywall panel and work out.

5. When the ceiling is finished, cut and install wall panels. Carefully measure for any cutouts in the drywall, including electrical outlets, switches, or light fixtures.

6. Space the nails 6 inches apart along studs, but start nailing 4 inches from the ceiling.

Image credit

http://z.about.com/d/homerenovations/1/0/b/0/-/-/fastendrywall3.JPG

Large Drywall Hole

Sometimes a wall or ceiling can be damaged by water or other reasons cause large drywall hole.

Without a drywall repair kit how can you fix it?

Some effective tips are mentioned below..

1.  First pick up an utility knife & cut scrap piece of drywall into square or rectangle.
2.  Scrap piece must be a little bigger than damaged area or hole.
3.  Purchase drywall patch from hardware store. Set it against damaged area and lightly trace around it with pencil or something.
4.  Now with keyhole saw cut out outlined area.
5.  Hole in drywall will be exactly the same size as patch.
6.  Install small board about 6 inches longer than long dimension of hole to hold wallboard patch in place.
7.  Now put board into hole, center it horizontally, and hold it firmly against inside of wallboard. Use screw to fix it.
8.  To hold patch in place, use spackling compound as glue.
9.  You need a backing board to fix a large drywall hole.
10. Once compound is dry, fill patch outline and cover exposed screw heads with spackling or joint compound.
11. Then prime and paint.

Image Credit:

http://i.ehow.com/images/GlobalPhoto/Articles/5203253/cutexcessaroundholecleanly-main_Full.jpg

Small Drywall Hole

If you want to repair a small drywall hole without a kit, follow these directions:

You will need the following items mentioned below..

* Clean tin can lid
* Tape measure
* Keyhole saw
* Awl
* Thin wire or string
* Scissors or wire cutters
* Scrap wood
* Putty knife
* Drywall patching compound
* Sandpaper
* Primer and paint
* Paintbrushes

Effective Tips Are Mentioned Below..

1.  First you have to prepare tin can lid that is at least 11/2 inches more in diameter than hole in drywall for backing piece.
2.  Use keyhole saw to cut out narrow horizontal slit in wall on each side of hole.
3.  Measurement the hole and both narrow slits should equal diameter of lid so you can insert lid sideways into hole.
4.  Now use awl to punch two holes in center of lid. Thread 12-inch piece of wire or string through holes.
5.  Holding ends of wire. Slide lid through slit. Still holding wire, pull lid toward you until it’s flat against inside of wall.
6.  Hold in place, set stick of scrap wood over hole on outside of wall and twist wire tightly over stick.
7.  Now time to use putty knife to apply premixed drywall patching compound over patch following manufacturer’s instructions.
8.  You can also mix plaster of paris with water to make thick paste.
9.  Pack plaster into hole against backing and behind stick.
10. Let patch dry until it turns bright white, typically at least 24 hours.
11. When dry, cut string or wire and remove stick.

You have to finish patch. Fill it completely with more drywall patching compound to make patch level with wall surface. Use prime, and paint after drying.

Image Credit:

http://activerain.com/image_store/uploads/4/7/1/6/7/ar125131941176174.jpg

Drywall Repair

There are so many things that cause small or big hole in the wall. Suppose if you open a door with too much force can produce a doorknob size hole in the wall. This kind of damage looks bad. But don’t worry, this type of large holes are easy to fix.

If you want to do it yourself, the easiest way is to purchase a drywall repair kit. First measure the hole, and visit your home improvement center or hardware store for a kit. You will find there are various sizes and types for different applications.

For example, a drywall patch for a ceiling is thicker than one for a wall. Before you use the kit, remove any loose plaster around the edges of the hole. Then apply drywall patch, you need to follow manufacturer’s instructions.

Now what are looking for? Try these:

* Materials you need: Repairing tools are not enough to do the job. You will often need various materials, such as drywall or lumber to complete a task.

Image Credit

http://www.raftertales.com/wp-content/uploads/2007/11/drywall-repair.jpg

Drywall Services

Drywall is a common or modern building material. Typically made of a layer of gypsum plaster pressed between two thick sheets of paper, then dried. Drywall is used globally for the finish construction of interior walls and ceilings. Drywall, also known as plasterboard, sheetrock or gypsum board. Drywall has a number of advantages over plaster. Drywall covers interior structures like beams and joists and provide a flat surface for papering or painting.

Drywall is used for interior wall surfacing used in new home construction and existing home repair and renovation.

The name ‘Drywall’ came from the fact that it went on ‘dry’ versus ‘wet’ like plaster. It has several common names of this product include:

# Drywall
# Gyp Board
# Gypsum Board
# Plaster Board
# Wallboard

We at Precision Painting Plus provide drywall services in Long Island-New York. We do every custom job from small to big. Just watch how we transform your wall looking newer quickly. We care your home, even take care to each and every little things. Everything will be protected before and while drywall process is going on. We have experienced professionals to help. They will take care of your budget. We have some plans for your drywall job. We provide a professional drywall services at low cost. Also we offer a Price Protection Plan for you. We are licensed & well insured to protect you. After finish our tasks we provide a complete job site cleanup facility.

Our Service areas for drywall services:

We provide the best quality drywall services at NASSAU COUNTY, QUEENS COUNTY, SUFFOLK, BROOKLYN, BRONX, STATEN ISLAND AND WESTCHESTER in Long Island-New York.